Manual pages - MX5 Manual | Mazda MX5 (Mk4) 2015+

Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

< Previous Next >

DTC P0711:00 [TCM (SJ6A-EL)]

DTC P0711:00	TFT sensor: Sensor malfunction
DETECTION CONDITION	Vehicle condition: While driving in D or R position with engine rotating Status: Detects no change in ATF temperature Period: Confirmed 1 time continuously for 10 min or more
FAIL-SAFE FUNCTION	Performs control with the ATF temperature of 80 °C {176 °F}. Inhibits learning control.
POSSIBLE CAUSE	TFT sensor malfunction TCM connector or terminal malfunction TCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic procedure

STEP	INSPECTION		ACTION
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture of the PC function. Record the freeze frame data/snap shot data.	—	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
		No	Go to the next step.
3	INSPECT FOR DTC Switch the ignition off, then ON (engine off or on). Perform the DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [TCM (SJ6A-EL)].) Are any other DTCs output?	Yes	Follow the applicable DTC inspection procedure, then go to the next step. (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [TCM (SJ6A-EL)].)
		No	Go to the next step.
4	INSPECT TFT SENSOR Inspect the TFT sensor. (See TRANSMISSION FLUID TEMPERATURE (TFT) SENSOR INSPECTION [SJ6A-EL].) Is the TFT sensor normal?	Yes	Go to the next step.
		No	Replace the TFT sensor, then go to Step 6. (See TRANSMISSION FLUID TEMPERATURE (TFT) SENSOR REMOVAL/INSTALLATION [SJ6A-EL].)
5	INSPECT TCM CONNECTOR FOR POOR CONNECTION Switch the ignition off. Disconnect the TCM connector. Inspect for poor connection (such as damaged/pulled-out pins, corrosion). Are terminals normal?	Yes	Go to the next step.
		No	Repair or replace the connector and/or terminal, then go to the next step.
6	VERIFY SAME DTC IS NOT PRESENT Always reconnect all disconnected connectors. Clear the DTC using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [TCM (SJ6A-EL)].) Perform the following procedure to ensure that the DTC has been resolved: Start the engine. Warm-up the engine to normal operating temperature. Drive the vehicle in D position for 10 min or more. Gradually slow down and stop the vehicle. Switch the ignition off. Start the engine. Drive the vehicle in D position for 10 min or more. Perform the DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [TCM (SJ6A-EL)].) Is the same DTC present?	Yes	Replace the TCM, then go to the next step. (See TCM REMOVAL/INSTALLATION [SJ6A-EL].)
		No	Go to the next step.
7	VERIFY DTC TROUBLESHOOTING COMPLETED Clear the DTC using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [TCM (SJ6A-EL)].) Perform the DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [TCM (SJ6A-EL)].) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [TCM (SJ6A-EL)].)
		No	DTC troubleshooting completed.

< Previous Next >

This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com

We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.