Manual pages - MX5 Manual | Mazda MX5 (Mk4) 2015+

Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

< Previous Next >

DTC C1035:11 [EVP CONTROL UNIT]

DTC	C1035:11	Electric vacuum pump relay 1: short to ground
DETECTION CONDITION		Resistance between the EVP control unit terminal C circuit and ground is less than 10 m ohm.
FAIL-SAFE FUNCTION		Refer to “Fail-safe function table”. (See DTC TABLE [EVP CONTROL UNIT].)
POSSIBLE CAUSE		Short to ground circuit in electric vacuum pump relay 1 circuit EVP control unit malfunction
SYSTEM WIRING DIAGRAM		—

Diagnostic Procedure

Step	Inspection		Action
1	RECORD SNAPSHOT DATA AND DIAGNOSTIC MONITORING TEST RESULTS TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture function of the PC. Record the snapshot data and DIAGNOSTIC MONITORING TEST RESULTS (fuel system related) on the repair order.	—	Go to the next step.
2	VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY OTHER RELATED DTCs OCCURRING Using the M-MDS, perform the EVP control unit DTC inspection. (See DTC INSPECTION [EVP CONTROL UNIT].) Is the DTC C101C:73 stored?	Yes	Go to the applicable DTC inspection. (See DTC C101C:73 [EVP CONTROL UNIT].)
		No	Go to the next step.
3	DETERMINE WHETHER MALFUNCTION IS PAST OR PRESENT NOTE: When clearing the DTC, the snap shot data is also cleared at the same time. Snap shot data is recorded if it is not recorded in Step 1. Using the M-MDS, clear the DTC from the EVP control unit. (See CLEARING DTC [EVP CONTROL UNIT].) Switch the ignition ON (engine off). Using the M-MDS, perform the EVP control unit DTC inspection. (See DTC INSPECTION [EVP CONTROL UNIT].) Is the same DTC present?	Yes	Replace the EVP control unit, then go to Step 7. (See EVP CONTROL UNIT REMOVAL/INSTALLATION.)
		No	Go to the next step.
4	VERIFY DTC REPEATABILITY Switch the ignition ON (engine off). Access the following EVP control unit PIDs using the M-MDS: VP_MV VP_PV Access the simulation item VPS_FBK using the M-MDS. Verify PID VP_MV and VP_PV when the electric vacuum pump is operated by simulation item VPS_FBK. Are VP_MV and VP_PV PIDs within specification? Specification: VP_MV: Below 0.8 V (VPS_FBK On), 4.1—8.7 V (VPS_FBK Off) VP_PV: 8.0—17.4 V (VPS_FBK On), 4.1—8.7 V (VPS_FBK Off)	Yes	Go to the next step.
		No	Replace the EVP control unit, then go to Step 7. (See EVP CONTROL UNIT REMOVAL/INSTALLATION.)
5	DRIVE VEHICLE THEN VERIFY DTC REPEATABILITY BASED ON SERVICE QUESTIONING RESULTS AND SNAP SHOT DATA Switch the ignition ON (engine off). Access the following EVP control unit PIDs using the M-MDS: VP_MV VP_PV VPS_FBK Drive the vehicle based on the service questions content and snap shot data driving conditions. Are VP_MV and VP_PV PIDs within specification, while the vehicle is driven? Specification: VP_MV: Below 0.8 V (VPS_FBK On), 4.1—8.7 V (VPS_FBK Off) VP_PV: 8.0—17.4 V (VPS_FBK On), 4.1—8.7 V (VPS_FBK Off)	Yes	Go to the next step.
		No	Replace the EVP control unit, then go to Step 7. (See EVP CONTROL UNIT REMOVAL/INSTALLATION.)
6	VERIFY DTC REPEATABILITY AND DETERMINE IF MALFUNCTION CAUSE IS EVP CONTROL UNIT Using the M-MDS, clear the DTC from the EVP control unit. (See CLEARING DTC [EVP CONTROL UNIT].) Switch the ignition ON (engine off). Using the M-MDS, perform the EVP control unit DTC inspection. (See DTC INSPECTION [EVP CONTROL UNIT].) Is the same DTC present?	Yes	Replace the EVP control unit, then go to the next step. (See EVP CONTROL UNIT REMOVAL/INSTALLATION.)
		No	DTC troubleshooting completed. Explain to the customer that there are no malfunctions with the vehicle based on the contents of the servicing.
7	VERIFY NO DTC IS PRESENT Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [EVP CONTROL UNIT].)
		No	DTC troubleshooting completed.

< Previous Next >

This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com

We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.