Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5
Home

 

< Previous   Next >

DTC P0365:00 [PCM (SKYACTIV-G 2.0)]

DTC P0365:00

Exhaust CMP sensor circuit problem

DETECTION CONDITION

  • The exhaust CMP sensor input signal pattern, received while the crankshaft rotates 24 times, is incorrect.

  • Cylinder identification is not completed while the crankshaft rotates 15 times.

    Diagnostic support note

  • This is a continuous monitor (CCM).

  • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

  • FREEZE FRAME DATA/Snapshot data is available.

  • DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

  • Stops fuel injection

  • Stops ignition

POSSIBLE CAUSE

  • Exhaust CMP sensor connector or terminals malfunction

  • Short to ground or open circuit in exhaust CMP sensor power supply circuit

    • Short to ground in wiring harness between ENGINE2 15 A fuse and exhaust CMP sensor terminal A

    • ENGINE2 15 A fuse malfunction

    • Open circuit in wiring harness between main relay terminal C and exhaust CMP sensor terminal A

  • Short to ground in wiring harness between exhaust CMP sensor terminal C and PCM terminal 1T

  • PCM connector or terminals malfunction

  • Short to power supply in wiring harness between exhaust CMP sensor terminal C and PCM terminal 1T

  • Exhaust CMP sensor signal circuit and ground circuit are shorted to each other

  • Open circuit in wiring harness between the following terminals:

    • Exhaust CMP sensor terminal C—PCM terminal 1T

    • Exhaust CMP sensor terminal B—PCM terminal 1X

  • Exhaust CMP sensor malfunction

    • Exhaust CMP sensor is dirty

    • Exhaust CMP sensor pulse wheel malfunction

  • CKP sensor connector or terminals malfunction

  • Loose timing chain or improper valve timing

  • PCM malfunction

Diagnostic Procedure

STEP

INSPECTION

ACTION

1

 RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION

NOTE:

  • Recording can be facilitated using the screen capture function of the PC.

  • Record the FREEZE FRAME DATA/snapshot data on the repair order.

—

Go to the next step.

2

 VERIFY RELATED REPAIR INFORMATION AVAILABILITY

  • Verify related Service Bulletins and/or on-line repair information availability.

  • Is any related repair information available?

Yes

Perform repair or diagnosis according to the available repair information.

  • If the vehicle is not repaired, go to the next step.

No

Go to the next step.

3

 VERIFY RELATED PENDING CODE AND/OR DTC

Yes

Go to the applicable PENDING CODE or DTC inspection.

(See DTC TABLE [PCM (SKYACTIV-G 2.0)].)

No

Go to the next step.

4

 INSPECT EXHAUST CMP SENSOR CONNECTOR CONDITION

  • Switch the ignition off.

  • Disconnect the exhaust CMP sensor connector.

  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

  • Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 14.

No

Go to the next step.

5

 INSPECT EXHAUST CMP SENSOR POWER SUPPLY CIRCUIT FOR SHORT TO GROUND OR OPEN CIRCUIT

  • Verify that the exhaust CMP sensor connector is disconnected.

  • Switch the ignition ON (engine off).

    NOTE:

    • Another DTC may be stored by the PCM detecting an open circuit.

  • Measure the voltage at the exhaust CMP sensor terminal A (wiring harness-side).

  • Is the voltage B+?

Yes

Go to the next step.

No

Inspect the ENGINE2 15 A fuse.

  • If the fuse is blown:

    • Refer to the wiring diagram and verify whether or not there is a common connector between ENGINE2 15 A fuse and exhaust CMP sensor terminal A.

        • If there is a common connector:

      • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.

      • Repair or replace the malfunctioning part.

        If there is no common connector:

      • Repair or replace the wiring harness which has a short to ground.

      • Replace the fuse.

  • If the fuse is damaged:

    • Replace the fuse.

  • If the fuse is normal:

    • Refer to the wiring diagram and verify whether or not there is a common connector between main relay terminal C and exhaust CMP sensor terminal A.

        • If there is a common connector:

      • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.

      • Repair or replace the malfunctioning part.

        If there is no common connector:

      • Repair or replace the wiring harness which has an open circuit.

Go to Step 14.

6

 INSPECT EXHAUST CMP SENSOR SIGNAL CIRCUIT FOR SHORT TO GROUND

  • Verify that the exhaust CMP sensor connector is disconnected.

  • Switch the ignition off.

  • Inspect for continuity between exhaust CMP sensor terminal C (wiring harness-side) and body ground.

  • Is there continuity?

Yes

Disconnect the PCM connector and inspect the wiring harness for short to ground.

  • If the short to ground circuit could be detected in the wiring harness:

    • Refer to the wiring diagram and verify whether or not there is a common connector between exhaust CMP sensor terminal C and PCM terminal 1T.

        • If there is a common connector:

      • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.

      • Repair or replace the malfunctioning part.

        If there is no common connector:

      • Repair or replace the wiring harness which has a short to ground.

Go to Step 14.

No

Go to the next step.

7

 INSPECT PCM CONNECTOR CONDITION

  • Disconnect the PCM connector.

  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

  • Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 14.

No

Go to the next step.

8

 INSPECT EXHAUST CMP SENSOR SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY

  • Verify that the exhaust CMP sensor and PCM connectors are disconnected.

  • Switch the ignition ON (engine off).

    NOTE:

    • Another DTC may be stored by the PCM detecting an open circuit.

  • Measure the voltage at the exhaust CMP sensor terminal C (wiring harness-side).

  • Is the voltage 0 V?

Yes

Go to the next step.

No

Refer to the wiring diagram and verify whether or not there is a common connector between exhaust CMP sensor terminal C and PCM terminal 1T.

    If there is a common connector:

  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply.

  • Repair or replace the malfunctioning part.

    If there is no common connector:

  • Repair or replace the wiring harness which has a short to power supply.

Go to Step 14.

9

 INSPECT EXHAUST CMP SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER

  • Verify that the exhaust CMP sensor and PCM connectors are disconnected.

  • Switch the ignition off.

  • Inspect for continuity between exhaust CMP sensor terminals C and B (wiring harness-side).

  • Is there continuity?

Yes

Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:

  • Exhaust CMP sensor terminal C—PCM terminal 1T

  • Exhaust CMP sensor terminal B—PCM terminal 1X

    If there is a common connector:

  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other.

  • Repair or replace the malfunctioning part.

    If there is no common connector:

  • Repair or replace the wiring harness which has a short to each other.

Go to Step 14.

No

Go to the next step.

10

 INSPECT EXHAUST CMP SENSOR CIRCUIT FOR OPEN CIRCUIT

  • Verify that the exhaust CMP sensor and PCM connectors are disconnected.

  • Inspect for continuity between the following terminals (wiring harness-side):

    • Exhaust CMP sensor terminal C—PCM terminal 1T

    • Exhaust CMP sensor terminal B—PCM terminal 1X

  • Is there continuity?

Yes

Go to the next step.

No

Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:

  • Exhaust CMP sensor terminal C—PCM terminal 1T

  • Exhaust CMP sensor terminal B—PCM terminal 1X

    If there is a common connector:

  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.

  • Repair or replace the malfunctioning part.

    If there is no common connector:

  • Repair or replace the wiring harness which has an open circuit.

Go to Step 14.

11

 INSPECT EXHAUST CMP SENSOR

Yes

Replace the exhaust CMP sensor, then go to Step 14.

(See CAMSHAFT POSITION (CMP) SENSOR REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)

No

Go to the next step.

12

 INSPECT CKP SENSOR CONNECTOR CONDITION

  • Switch the ignition off.

  • Disconnect the CKP sensor connector.

  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

  • Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 14.

No

Go to the next step.

13

 VERIFY ASSEMBLY CONDITION OF TIMING CHAIN

Yes

Repair or replace the malfunctioning part.

Assemble the timing chain using the correct timing, then go to the next step.

(See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)

No

Go to the next step.

14

 VERIFY DTC TROUBLESHOOTING COMPLETED

Yes

Repeat the inspection from Step 1.

Go to the next step.

No

Go to the next step.

15

 VERIFY AFTER REPAIR PROCEDURE

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [PCM (SKYACTIV-G 2.0)].)

No

DTC troubleshooting completed.
< Previous   Next >
 

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

COPYRIGHT NOTICE:
This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com
LIMITATION OF LIABILITY:
We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.