Manual pages - MX5 Manual | Mazda MX5 (Mk4) 2015+

Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

< Previous Next >

DTC P2610:00 [PCM (SKYACTIV-G 2.0)]

DTC P2610:00	Malfunction in instrument cluster
DETECTION CONDITION	Malfunction detected in instrument cluster. Diagnostic support note This is a continuous monitor (CCM). The check engine light illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM. PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle. FREEZE FRAME DATA/Snapshot data is available. DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	The fast idle up correction for the drive-by-wire control is inhibited.
POSSIBLE CAUSE	Instrument cluster power supply circuit malfunction (in this case, the instrument cluster records DTC U3003:16.) Instrument cluster malfunction PCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture function of the PC. Record the FREEZE FRAME DATA/snapshot data on the repair order.	—	Go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY STORED DTC IN INSTRUMENT CLUSTER Switch the ignition off, then ON (engine off). Retrieve the instrument cluster DTC using the M-MDS. (See DTC INSPECTION [INSTRUMENT CLUSTER].) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [INSTRUMENT CLUSTER].)
3		No	Go to the next step.
4	INSPECT INSTRUMENT CLUSTER BACKUP VOLTAGE CIRCUIT Switch the ignition off. Remove the MAIN 200 A fuse, ROOM 25 A fuse and INTERIOR 15 A fuse. Inspect the MAIN 200 A fuse, ROOM 25 A fuse and INTERIOR 15 A fuse. Is there any malfunction?	Yes	Replace the malfunctioning fuse. Switch the ignition ON (engine on) and wait for 10 s or more. Switch the ignition off. Go to the next step.
4		No	Replace the instrument cluster, then go to the next step. (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
5	VERIFY DTC TROUBLESHOOTING COMPLETED Always reconnect all disconnected connectors. NOTE: DTC P2610:00 can be cleared by performing the engine start and stop procedure. Start the engine. Stop the engine. Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0)].) Perform the KOER self test. (See KOEO/KOER SELF TEST [PCM (SKYACTIV-G 2.0)].) Is the PENDING CODE for this DTC present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0].) Go to the next step.
5		No	Go to the next step.
6	VERIFY AFTER REPAIR PROCEDURE Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0)].) Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-G 2.0)].)
6		No	DTC troubleshooting completed.

< Previous Next >

This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com

We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.