MX5 mk4 Manual
Home bodyshop manual wiring diagram workshop manual service highlights transmission overhaul

Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5
Home

 

< Previous   Next >

CONVERTIBLE TOP ADJUSTMENT

Top Lock Ajustment

1. Remove the top lock cover.(See TOP LOCK REMOVAL/INSTALLATION.)
2. Loosen the top lock installation screws and adjust the top lock position.

3. Tighten the top lock installation screws.(See TOP LOCK REMOVAL/INSTALLATION.)
4. Close the convertible top and secure the top lock.
5. Verify that the gap between the windshield garnish and the convertible top is within the specification.

    Standard clearance
  • A: 5—9 mm {0.2—0.3 in}

  • If not within the specification, repeat from Step 2 to Step 5 until the clearance between the windshield garnish and the convertible top is within the specification.

6. Verify that the top lock can be secured/released smoothly.
7. Install the top lock cover.(See TOP LOCK REMOVAL/INSTALLATION.)

Female Wedge Ajustment

NOTE:

  • The female wedge can be adjusted on the left side only.

1. Loosen the female wedge installation screws and adjust the female wedge position.(See FEMALE WEDGE REMOVAL/INSTALLATION.)
2. Tighten the female wedge installation screws.(See FEMALE WEDGE REMOVAL/INSTALLATION.)
3. Verify that the top lock can be secured/released smoothly.

Link Weatherstrip Ajustment

Link weatherstrip No.1 ajustment
1. Partially peel back the link weatherstrip No.1.
2. Loosen the retainer No.1 installation screws and adjust the retainer No.1 position.

3. Tighten the retainer No.1 installation screws.
4. Install the link weatherstrip No.1.
5. Verify that the convertible top opens/closes smoothly.
6. Verify that the top lock can be secured/released smoothly.
7. Verify that the door glass can be opened/closed smoothly.
Link weatherstrip No.2 ajustment
1. Adjust the convertible top opening/closing position to the area where the fastener is visible as shown in the figure.

2. Remove the fastener.
3. Partially peel back link weatherstrip No.2 by pulling it in the direction of the arrow shown in the figure.

4. Loosen the retainer No.2 and retainer No.3 installation screws and adjust the retainer No.2 and retainer No.3 position.

5. Tighten the retainer No.2 and retainer No.3 installation screws.
6. Install the link weatherstrip No.2.
7. Verify that the convertible top opens/closes smoothly.
8. Verify that the top lock can be secured/released smoothly.
9. Verify that the door glass can be opened/closed smoothly.
< Previous   Next >
 

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

COPYRIGHT NOTICE:
This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com
LIMITATION OF LIABILITY:
We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.
Site design © MX5 Docs 2019
Privacy policy
Cookies
X
We use cookies to improve your experience on
our site. By using our site you consent to cookies.
Learn more
I Agree