Manual pages - MX5 Manual | Mazda MX5 (Mk4) 2015+

Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

< Previous Next >

DTC B10A0:64 [BCM]

Description	Wiper and washer switch error signal received
Detection condition	BCM receives error signals from the start stop unit for 5 s or more with the ignition switched ON (engine off or on).
Fail-safe	Wiper system Continue the controls prior to the wiper malfunction detection. Washer system Stop the washer control.
Possible cause	Start stop unit malfunction Wiper and washer switch malfunction BCM malfunction
System wiring diagram	Not applicable

Diagnostic Procedure

Step	Inspection		Action
1	VERIFY BCM DTCs AGAIN Clear the DTC for the BCM using the M-MDS. (See CLEARING DTC [BCM].) Switch the ignition ON (engine off or on) and wait for 5 s or more. Retrieve the BCM DTCs using the M-MDS. (See DTC INSPECTION [BCM].) Is the same DTC displayed?	Yes	Go to the next step.
		No	Go to Step 6.
2	DETERMINE MALFUNCTIONING LOCATION BY PERFORMING PID/DATA MONITOR INSPECTION Using the M-MDS, display the following PIDs for the start stop unit. (See PID/DATA MONITOR INSPECTION [START STOP UNIT].) WASHER_F WIP_F_INT WIP_F_LOW Does the PID monitoring value switch correctly according to the wiper and washer switch operation?	Yes	Go to Step 4. (Circuit between wiper and washer switch and start stop unit is normal)
		No	Go to the next step.
3	INSPECT WIPER AND WASHER SWITCH Inspect the wiper and washer switch. (See WIPER AND WASHER SWITCH INSPECTION.) Is the wiper and washer switch normal?	Yes	Replace the start stop unit, then go to Step 5. (See START STOP UNIT REMOVAL/INSTALLATION.)
		No	Replace the wiper and washer switch, then go to Step 5. (See WIPER AND WASHER SWITCH REMOVAL/INSTALLATION.)
4	DETERMINE MALFUNCTIONING LOCATION BY PERFORMING PID/DATA MONITOR INSPECTION Using the M-MDS, display PID WIP_F_SW for the BCM. (See PID/DATA MONITOR INSPECTION [BCM]) Does the PID monitoring value switch correctly according to the wiper and washer switch operation?	Yes	Go to the next step. (Circuit between start stop unit and BCM is normal.)
		No	Replace the start stop unit, then go to the next step. (See START STOP UNIT REMOVAL/INSTALLATION.)
5	VERIFY THAT REPAIRS HAVE BEEN COMPLETED Clear the DTC for the BCM using the M-MDS. (See CLEARING DTC [BCM].) Switch the ignition ON (engine off or on) and wait for 5 s or more. Retrieve the BCM DTCs using the M-MDS. (See DTC INSPECTION [BCM].) Is the same DTC displayed?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the BCM. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION.) Go to the next step.
		No	Go to the next step.
6	VERIFY IF OTHER DTCs DISPLAYED Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [BCM].)
		No	DTC troubleshooting completed.

< Previous Next >

This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com

We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.