Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5
Home

 

< Previous   Next >

DTC B0001:11/B0001:12/B0001:13/B0001:19/B0001:1A [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)]

System malfunction location

  • B0001:11: Driver-side air bag module circuit short to body ground

  • B0001:12: Driver-side air bag module circuit short to power supply

  • B0001:13: Driver-side air bag module circuit open circuit or resistance high

  • B0001:19: Short circuit to driver-side air bag module and other air bag module circuits

  • B0001:1A: Driver-side air bag module circuit resistance low

Detection condition

WARNING:

  • Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.

  • Resistance other than 1.37–6.33 ohms detected in driver-side air bag module circuit

  • Wiring harness between driver-side air bag module and SAS control module has malfunction

Fail-safe function

Not applicable

Possible cause

  • Clock spring connector malfunction

  • Clock spring malfunction

  • Short circuit to power supply or body ground in the wiring harness between the clock spring and SAS control module

  • Open circuit in the wiring harness between the clock spring and SAS control module

  • Driver-side air bag module malfunction

  • SAS control module malfunction

Diagnostic Procedure

Step

Inspection

Action

1

 INSPECT DRIVER-SIDE AIR BAG MODULE CONNECTOR

WARNING:

Yes

Replace clock spring.

(See CLOCK SPRING REMOVAL/INSTALLATION [STANDARD DEPLOYMENT CONTROL SYSTEM].)

Then go to Step 7.

No

Go to the next step.

2

 INSPECT CLOCK SPRING

NOTE:

  • Inspect the clock spring wiring harness for continuity while shaking it.

  • Is there continuity?

Yes

Go to the next step.

No

Replace clock spring.

(See CLOCK SPRING REMOVAL/INSTALLATION [STANDARD DEPLOYMENT CONTROL SYSTEM].)

Then go to Step 7.

3

 INSPECT DRIVER-SIDE AIR BAG MODULE CIRCUIT FOR SHORT TO GROUND

NOTE:

  • Inspect for continuity while shaking the wiring harness between the SAS control module and clock spring.

  • Is there continuity?

Yes

Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and clock spring terminal.

    If there is a common connector:

  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.

  • Replace the malfunctioning part.

    If there is no common connector:

  • Replace the wiring harness which has a short to ground.

Go to Step 7.

No

Go to the next step.

4

 INSPECT DRIVER-SIDE AIR BAG MODULE CIRCUIT FOR OPEN CIRCUIT

  • SAS control module and clock spring connectors are disconnected.

  • Inspect for continuity between the following terminals (wiring harness-side):

    • Clock spring terminal 2B—SAS control module terminal 3C

    • Clock spring terminal 2A—SAS control module terminal 3G

NOTE:

  • Inspect for continuity while shaking the wiring harness between the SAS control module and clock spring.

  • Is there continuity?

Yes

Go to the next step.

No

Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and clock spring terminal.

    If there is a common connector:

  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.

  • Replace the malfunctioning part.

    If there is no common connector:

  • Replace the wiring harness which has an open circuit.

Go to Step 7.

5

 INSPECT DRIVER-SIDE AIR BAG MODULE CIRCUIT FOR SHORT TO POWER SUPPLY

  • SAS control module and clock spring connectors are disconnected.

  • Connect the negative battery cable.

    (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

  • Switch the ignition ON (engine off or on).

  • Measure the voltage at the following terminals (wiring harness-side):

    • SAS control module terminal 3C

    • SAS control module terminal 3G

NOTE:

  • Measure the voltage while shaking the wiring harness between the SAS control module and clock spring.

  • Is the voltage 0 V?

Yes

Go to the next step.

No

Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and clock spring terminal.

    If there is a common connector:

  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply.

  • Replace the malfunctioning part.

    If there is no common connector:

  • Replace the wiring harness which has a short to power supply.

Go to Step 7.

6

 INSPECT DRIVER-SIDE AIR BAG MODULE

Yes

Go to the next step.

No

Replace the driver-side air bag module.

(See DRIVER-SIDE AIR BAG MODULE REMOVAL [STANDARD DEPLOYMENT CONTROL SYSTEM].)

(See DRIVER-SIDE AIR BAG MODULE INSTALLATION [STANDARD DEPLOYMENT CONTROL SYSTEM].)

Then go to the next step.

7

 PERFORM SAS CONTROL MODULE DTC INSPECTION

Yes

Repeat the inspection from Step 1.

No

DTC troubleshooting completed.
< Previous   Next >
 

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

COPYRIGHT NOTICE:
This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com
LIMITATION OF LIABILITY:
We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.