Knowledge Base

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5
Home

 

< Previous   Next >

NET REMOVAL/INSTALLATION

WARNING:

CAUTION:

  • The elasticity of the nets (seat back side and seat cushion side) may decrease if exposed to direct sunlight (UV rays). Do not remove/install the seat back trim and disassemble/assemble the seats in an outdoor environment under direct sunlight (UV rays).

Net (Seat Back Side)

1. Switch the ignition OFF (LOCK).
2. Disconnect the negative battery cable and wait for 1 min or more.(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)
3. Remove the following parts:
a. Seat (See SEAT REMOVAL/INSTALLATION.)
b. Seat side cover(See SEAT SIDE COVER REMOVAL/INSTALLATION.)
c. Buckle(See BUCKLE REMOVAL/INSTALLATION)
d. Seat back component (See SEAT BACK COMPONENT REMOVAL/INSTALLATION.)
e. Seat back trim (See SEAT BACK TRIM REMOVAL/INSTALLATION.)
4. Remove the C-rings.

5. Insert a precision flathead screwdriver in the position shown in the figure.

6. Move the precision flathead screwdriver in the direction of the arrow shown in the figure to detach the wire from the hook.
7. Detach all of the wires from the hooks and remove the net.
8. Install in the reverse order of removal. (See Net Installation Note.)

Net (Seat Cushion Side)

1. Switch the ignition OFF (LOCK).
2. Disconnect the negative battery cable and wait for 1 min or more.(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)
3. Remove the following parts:
a. Seat (See SEAT REMOVAL/INSTALLATION.)
b. Seat side cover(See SEAT SIDE COVER REMOVAL/INSTALLATION.)
c. Buckle(See BUCKLE REMOVAL/INSTALLATION)
d. Seat back component (See SEAT BACK COMPONENT REMOVAL/INSTALLATION.)
e. Seat cusion trim (See SEAT CUSHION TRIM REMOVAL/INSTALLATION.)
4. Remove the fasteners.

5. Insert a precision flathead screwdriver in the position shown in the figure.

6. Move the precision flathead screwdriver in the direction of the arrow shown in the figure to detach the wire from the hook.
7. Detach all of the wires from the hooks and remove the net.

  • If the cushion supporter is to be removed, remove it using the following procedure.

8. Move hooks A in the order of arrows (1) and (2) shown in the figure and detach them from hooks B.

9. Remove the cushion supporter.
10. Install in the reverse order of removal. (See Net Installation Note.)

Net Installation Note

  • Install the net using the following procedure.

1. Insert a precision flathead screwdriver in the position shown in the figure.

2. Move the precision flathead screwdriver in the direction of the arrow shown in the figure and install the wire onto the hook.
< Previous   Next >
 

Free to use workshop manual for your 2015+ Mk4 'ND' Mazda MX-5

COPYRIGHT NOTICE:
This fan site is not affiliated with Mazda, and is intended for personal, or commercial use only. The content of our web pages is for general information purposes only and is presented “as is”. We give no assurance or warranty regarding the accuracy of the contents. Readers should do their due diligence and seek the advice of an appropriately certified automotive technician before attempting any steps on this site. Original content provided by Mazda North America. The content of the manual is copyright under DMCA to: full.metal.resistor@gmail.com
LIMITATION OF LIABILITY:
We accept no responsibility for errors, inaccuracies, or omissions found on these pages. Additionally, we hereby exclude liability for any demands, claims, damages or losses of any kind with regard to any content or information provided on our web-site, including but not limited to incidental or consequential damages, direct or indirect loss, compensatory damages, loss of profits, or otherwise. By using this manual you assume full liablity for any procedures carried out on your vehicle, and are responsible for the vehicle remaining road legal and safe.