DIAGNOSTIC ASSIST FUNCTION [CONNECTIVITY MASTER UNIT]

Activation Procedure

Using commander switch

1. Switch the ignition to ACC or ON (engine off or on).

2. Press the following buttons simultaneously for 2 s or more.

• Volume dial

• AUDIO button

• FAVORITES button

Using center display

1. Switch the ignition to ACC or ON (engine off or on).

2. Display the display setting screen in the center display.

• Select [Settings] on the center display.

• Select [Screen] on the center display.

3. Operate the center display in the following order.

• Touch and hold the right upper area of the screen (area A in figure) until a beep is heard (approx. 5 s or more).

• Touch and hold the left upper area of the screen (area B in figure) until a beep is heard (approx. 5 s or more).

Diagnostic Assist Code Input Procedure

Diagnostic assist code input screen

^*1

Displayed while the diagnostic assist function is not performed.

^*2

Displayed while the diagnostic assist function is being performed.

Using commander switch

1. Input the diagnostic assist code by rotating the commander knob.

2. Press the commander knob.

3. Perform the inspection according to the diagnostic assist code list. (See Diagnostic Assist Code List.)

NOTE:

• If [- REJECTED] is displayed, the inspection cannot be performed because communication is not enabled between the related parts, or the conditions are not met even if communication is enabled. Therefore, verify the display [- REJECTED] referring to the following procedure. (See [- REJECTED] is displayed.)

Using center display

1. Input the diagnostic assist code by pressing the ???Diagnostic assist code input switch???.

2. Press ???ENTER???.

3. Perform the inspection according to the diagnostic assist code list. (See Diagnostic Assist Code List.)

NOTE:

• If [- REJECTED] is displayed, the inspection cannot be performed because communication is not enabled between the related parts, or the conditions are not met even if communication is enabled. Therefore, verify the display [- REJECTED] referring to the following procedure. (See [- REJECTED] is displayed.)

[- REJECTED] is displayed

1. Switch the ignition off.

2. Launch the diagnostic assist function. (See Activation Procedure.)

3. Input the diagnostic assist code. (See Diagnostic Assist Code Input Procedure.)

4. Verify that [- REJECTED] is not displayed.

• If [- REJECTED] is displayed, perform the DTC inspection or inspect the part related to the diagnostic content. (See DTC INSPECTION [CONNECTIVITY MASTER UNIT].)

Ending Procedure

1. While the inspection is being performed, press ???END??? to return to the diagnostic assist code input screen.

NOTE:

• The diagnostic assist function cannot be canceled while the diagnostic assist function is being inspected.

2. Cancel the diagnostic assist function by pressing ???EXIT???.

NOTE:

• If the diagnostic assist function is canceled, it returns to a different screen depending on the way in which the diagnostic assist function was launched.

• If launched using the commander switch: The screen directly before launching the diagnostic assist function

• If launched not using the commander switch: The display setting screen

Diagnostic Assist Code List

Diagnostic Assist Code ???01??? CD Player Inspection

1. Input diagnostic assist code ???01??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. After inputting the diagnostic assist code, insert the CD into the CD player within 10 s.

Inspection	Display of center display (Diagnostic result)	Content	Action
Launch the CD player inspection mode. Verify the inspection result.	CD OK	CD is normal After inspection, a malfunction is not detected.	The CD player is operating normally.
	CD Mechanical Linkage Failure	CD read failure Disc is not loaded normally due to a malfunction (damage or deformation) on disc or CD player malfunction.	Verify that CD is not damaged or deformed. If there is a malfunction: Re-perform the inspection using a normal CD. If there is no malfunction: Replace the CD player. (See CD PLAYER REMOVAL/INSTALLATION.)
	CD Signal Plausibility Failure	CD data format error Disc is loaded, but system detects disc which CD player cannot read.	Replace with a compatible CD. Replace with CD containing music data in the data format (CD-DA)/MP3/WMA (Windows Media Audio)/ACC (Advance Audio Coding).

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???02??? DTC Clear

1. Input diagnostic assist code ???02??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. Verify that all DTCs are cleared.

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???03/04/05/06??? DTC Inspection

1. Verify the module to be inspected for DTCs referring to the chart, then input the diagnostic assist code according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

NOTE:

• The combination of DTC and diagnostic assist code can be verified in the DTC table. (See DTC TABLE [CONNECTIVITY MASTER UNIT])

• Detection of DTCs is limited if the ignition is in the ACC position.

×: Applicable???: Not applicable

Diagnostic assist code	Modules which can be verified for DTC
	Connectivity master unit (CMU)	Tuner and amp unit (TAU)	CD player
03*1	×	×	×
04	×	???	???
05	???	×	???
06	???	???	×

^*1

List of DTCs which can detect diagnostic assist codes ???04???, ???05???, and ???06??? is displayed.

2. If a DTC is displayed, repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [CONNECTIVITY MASTER UNIT].)

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???09/53/57/68/69/93??? Software Version Verification

1. Verify the module to be inspected for the software version referring to the chart, then input the diagnostic assist code according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

Diagnostic assist code	Software version to be verified
09	CD player
53	Connectivity master unit (CMU) (overall entertainment system)
57	Connectivity master unit (CMU) (overall communication system between vehicle)
68	Center display (TFT LCD screen control system)
69	Center display (Touch panel control system)
93	Tuner and amp unit (TAU)

2. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???10/85??? Part Number Verification

1. Verify the module to be inspected for the part number referring to the chart, then input the diagnostic assist code according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

Diagnostic assist code	Module to be verified for part number
10	CD player
85	Tuner and amp unit (TAU)

2. Verify the part number.

NOTE:

• Only upper 4 digits of the part number are displayed.

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???25??? Antenna Control Output Condition Inspection

1. Input diagnostic assist code ???25??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. Inspect the malfunctioning location according to the following table:

CAUTION:

• Even if the system is normal, radio reception may be difficult depending on where the system is inspected (indoors/outdoors, or conditions at the location). Before inspecting the system, verify that radio reception is adequate.

• When performing the inspection, select a frequency (radio station) with optimum reception in the area.

Inspection	Display of center display (Diagnostic result)	Action
Launch the antenna control output condition inspection mode.	ANT-ON	Good sound quality	System is normal.
		Bad sound quality	Inspect the rod antenna and antenna feeder. (See ROD ANTENNA INSPECTION.) (See ANTENNA FEEDER NO.2 INSPECTION.) If the rod antenna or antenna feeder is malfunctioning: Replace the malfunctioning part. (See ROD ANTENNA REMOVAL/INSTALLATION.) (See ANTENNA FEEDER NO.2 REMOVAL/INSTALLATION.) If the rod antenna and antenna feeder are normal: Replace the tuner and amp unit (TAU). (See TUNER AND AMP UNIT (TAU) REMOVAL/INSTALLATION.)
	ANT-OFF	Output cannot be verified	Replace the tuner and amp unit (TAU). (See TUNER AND AMP UNIT (TAU) REMOVAL/INSTALLATION.)

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???58??? Configuration Information Verification

1. Input diagnostic assist code ???58??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. Verify the configuration information.

Display of center display	Content
Destination	Destination information
CMU Types	Recognition condition whether connectivity master unit (CMU) is equipped or not

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???59??? Individual Number Verification

1. Input diagnostic assist code ???59??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. Verify the individual number of the connectivity master unit (CMU).

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???61??? Vehicle Signal Verification

1. Input diagnostic assist code ???61??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. Verify the vehicle signal.

Display of center display (Diagnostic result)	Content
Backup Camera	Rear mount camera signal input condition
ST-SW1	Steering switch signal (volume adjustment switch, cue/automatic band selector switch) input condition
ST-SW2	Steering switch signal (talk button, pick-up button, hang-up button) input condition
Commander	Commander switch signal input condition
GPS	GPS antenna signal input condition
Microphone	Microphone signal input condition
HUB1	Auxiliary jack/USB port/SD card slot hub1 signal input condition
NAVI (SD)	SD card insertion condition
CD/DVD	DVD/CD equipment recognition condition
DTV	TV tuner unit equipment recognition condition

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???65??? Switch Inspection

1. Input diagnostic assist code ???65??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. Perform the steering switch inspection or commander switch inspection.

NOTE:

• When the switch is operated, the switch operation content detected by the connectivity master unit (CMU) is displayed in the center display.

• If the switch operation content previously detected is being displayed in the center display, newly detected content is added over it.

Steering switch inspection

Inspection	Display of center display (Diagnostic result)	Action
Launch the switch inspection mode. Operate each switch of the steering switch. Does the display in the center display correspond to each operation?	ST-SW Talk Button Pressed: TALK button is pressed ST-SW Talk Button Released: TALK button is released ST-SW Pick-Up Button Pressed: Pick-up button is pressed ST-SW Pick-Up Button Released: Pick-up button is released ST-SW Hang-Up Button Pressed: Hang-up button is pressed ST-SW Hang-Up Button Released: Hang-up button is released ST-SW Volume + Button Pressed: Volume adjustment switch (+) is pressed ST-SW Volume + Button Released: Volume adjustment switch (+) is released ST-SW Volume - Button Pressed: Volume adjustment switch (-) is pressed ST-SW Volume - Button Released: Volume adjustment switch (-) is released ST-SW Seek + Button Pressed: Cue/Automatic band selector switch (UP) is pressed ST-SW Seek + Button Released: Cue/Automatic band selector switch (UP) is released ST-SW Seek - Button Pressed: Cue/Automatic band selector switch (DOWN) is pressed ST-SW Seek - Button Released: Cue/Automatic band selector switch (DOWN) is released	Yes	The steering switch is normal.
		No	Inspect the steering switch. (See STEERING SWITCH INSPECTION.) If there is a malfunction: Replace the steering switch. (See STEERING SWITCH REMOVAL/INSTALLATION.) If the steering switch is normal: Replace the connectivity master unit (CMU). (See CONNECTIVITY MASTER UNIT (CMU) REMOVAL/INSTALLATION.)

Commander switch inspection

Inspection	Display of center display (Diagnostic result)	Action
Launch the switch inspection mode. Operate each button and knob of the commander switch. Does the display in the center display correspond to each operation?	Home Button Pressed: HOME button is pressed Home Button Released: HOME button is released Navi Button Pressed: NAV button is pressed Navi Button Released: NAV button is released Audio Button Pressed: AUDIO button is pressed Audio Button Released: AUDIO button is released Favorites Button Pressed: FAVORITES button is pressed Favorites Button Released: FAVORITES button is released Back Button Pressed: BACK button is pressed Back Button Released: BACK button is released Commander Pushed In: Commander knob is pressed Commander Released: Commander knob is released Tilt Up Pressed: Commander knob is tilted up Tilt Up Released: Commander knob is released from tilted up condition Tilt Right Pressed: Commander knob is tilted to the right Tilt Right Released: Commander knob is released from tilted right condition Tilt Down Pressed: Commander knob is tilted down Tilt Down Released: Commander knob is released from tilted down condition Tilt Left Pressed: Commander knob is tilted to the left Tilt Left Released: Commander knob is released from tilted left condition Commander Turned Clockwise: Commander knob is turned clockwise Commander Turned Counter Clockwise: Commander knob is turned counterclockwise Volume Knob Pushed In: Volume dial is pressed Volume Knob Released: Volume dial is released Volume Knob Turned Clockwise: Volume dial is turned clockwise Volume Knob Turned Counter Clockwise: Volume dial is turned counterclockwise	Yes	Commander switch is normal.
		No	Replace the commander switch. (See COMMANDER SWITCH REMOVAL/INSTALLATION.)

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???70??? Display/Touch Panel Inspection

1. Input diagnostic assist code ???70??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

NOTE:

• The display/touch panel inspection is repeated periodically until a same location in the center display is touched for 10 s or more.

Inspection	Display of center display (Diagnostic result)	Action
Launch the display/touch panel inspection mode. Verify the center display. Does the center display display normally?	If normal, [+] cursor is displayed centering around the touched area, and at the same time, the display switches in the following order. Unicolor screen in the following colors White???Black???Red???Green???Blue Horizontal-striped screen in black and the following colors Red???Green???Blue Vertical-striped screen in black and the following colors Red???Green???Blue Checkered screen in black and the following colors Red???Green???Blue Returns to 1.	Yes	Center display is normal.
		No	Replace the center display. (See CENTER DISPLAY REMOVAL/INSTALLATION.)

2. Continuously touch the same location for 10 s or more.

NOTE:

• If the display/touch panel inspection is finished, the diagnostic assist function is canceled without returning to the diagnostic assist code input screen.

• If the diagnostic assist function is canceled, it returns to a different screen depending on the way in which the diagnostic assist function was launched.

• If launched using the commander switch: The screen directly before launching the diagnostic assist function

• If launched not using the commander switch: The display setting screen

Diagnostic Assist Code ???72??? GPS Information Verification

1. Input diagnostic assist code ???72??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. Verify the GPS information.

NOTE:

• GPS reception signal is updated every 1 s.

Display of center display (Diagnostic result)	Content
Longitude (X)	Degree of longitude in GPS information of the current location
Latitude (Y)	Degree of latitude in GPS information of the current location
Absolute Time (Z)	Date and time information (GMT)
Number of Satellites	Number of satellites being received

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???84??? Manufacturer Name Verification

1. Input diagnostic assist code ???84??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

2. Verify the manufacturer name.

3. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???90??? Radio Reception Condition Inspection

1. Tune in the radio.

2. Input diagnostic assist code ???90??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

3. Inspect the malfunctioning location according to the following table:

CAUTION:

• Even if the system is normal, radio reception may be difficult depending on where the system is inspected (indoors/outdoors, or conditions at the location). Before inspecting the system, verify that radio reception is adequate.

• When performing the inspection, select a frequency (radio station) with optimum reception in the area.

Inspection	Display of center display (Diagnostic result)	Action
Start the radio reception condition inspection mode. Select frequency (radio station) by operating the commander knob. Verify the inspection result.	TAU AM Reception Level Test Result:10???5	Radio reception condition is normal Rod antenna, antenna feeder, and tuner and amp unit (TAU) are normal.
	TAU AM Reception Level Test Result:4???3	Radio reception condition is unstable Change frequencies and re-perform the inspection.
	TAU AM Reception Level Test Result:2???0	Radio reception is poor or not receivable Inspect the rod antenna and antenna feeder. (See ROD ANTENNA INSPECTION.) (See ANTENNA FEEDER NO.2 INSPECTION.) If the rod antenna or antenna feeder is malfunctioning: Replace the malfunctioning part. (See ROD ANTENNA REMOVAL/INSTALLATION.) (See ANTENNA FEEDER NO.2 REMOVAL/INSTALLATION.) If the rod antenna and antenna feeder are normal: Replace the tuner and amp unit (TAU). (See TUNER AND AMP UNIT (TAU) REMOVAL/INSTALLATION.)

4. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)

Diagnostic Assist Code ???94??? Speaker Inspection

1. Input diagnostic assist code ???94??? according to the diagnostic assist code input procedure. (See Diagnostic Assist Code Input Procedure.)

Inspection	Display of center display	Action
Launch the speaker inspection mode. Does each speaker output sound in the following order?: Without Bose® Door speaker (LH) and tweeter (LH) Door speaker (RH) and tweeter (RH) Driver-side headrest speaker (RH) Driver-side headrest speaker (LH) With Bose® Door speaker (LH) and tweeter (LH) Door speaker (RH) and tweeter (RH) Driver-side headrest speaker (RH) and passenger-side headrest speaker (RH) Driver-side headrest speaker (LH) and passenger-side headrest speaker (LH) Woofer	???	Yes	Without Bose® The following parts and wiring harness are normal: Each speaker Tuner and amp unit (TAU) Between tuner and amp unit (TAU) and each speaker With Bose® The following parts and wiring harness are normal: Each speaker Tuner and amp unit (TAU) Audio amplifier Between tuner and amp unit (TAU) and audio amplifier Between audio amplifier and each speaker
		No	Refer to the symptom troubleshooting. (See NO SOUND OUTPUT IN ALL MODES [ENTERTAINMENT SYSTEM [WITH CENTER DISPLAY]].)

2. Cancel the diagnostic assist function according to the ending procedure. (See Ending Procedure.)